![]() ![]() In short, I think what you’ve done so far should be all you need to do, but one of the wonderful things about pfsense is you can do more if you choose to, so it’s a great learning platform as well as a nice firewall. I’ve also noticed that pfsense works more reliably with IPv6 Prefix Delegation than my old Cisco ASA did, but so far I’m only delegating a single IPv6 network to my LAN and haven’t had to do the extra config file work needed to get multiple IPv6 prefixes for any additional internal LAN (or VLAN) segments (that’s one of my upcoming projects). I do use a different IP network on my LAN though, so there’s no possibility of conflict in that regard. Also, I just now verified that even though the BGW gateway uses an RFC1918 management address you don’t have to clear the pfsense interface option to block incoming Private Address traffic because when you access the BGW all the traffic coming back is return traffic so pfsense recognizes it as part of an existing connection and forwards it appropriately. My pfsense WAN gets a public address, and I can still access the BGW320-500 gateway via its 192.168.1.254 address - no static routing needed, since the default route pfsense gets as part of the WAN DHCP process takes care of that. ![]() I have this exact same setup and what you’ve done is pretty much what I’ve done, but I didn’t manually assign a specific MAC address as part of the process since I was migrating from my old Cisco ASA 5506 firewall to a new pfsense box. Unless you have a large network (enterprise, not home) this only really applies to traffic leaving your network. You can manage QoS from pfSense too but just keep in mind that it isnt going to give you more bandwidth, it’s just going to prioritize what drops first when the pipe is full which is less of a problem the more bandwidth you have. If you changed your Wi-Fi name or password from the default, you can get it from the settings screen or Smart Home Manager. In regard to QoS, sometimes it’s really easy to hit a couple of buttons to optimize your connection (you will mostly want to prioritize real time voice and video traffic) but if not dont worry about it. The label on your Wi-Fi gateway or All-Fi Hub is the quickest way to get default Wi-Fi network info. While you are in your ISP device it would be a good idea to make sure uPnP is turned off, remote administration is turned off, and NTP is turned on, then take a long look at QoS. you will lose all settings, including the WIfi passwords you have set up. That should be all you need to do but these things vary a lot and sometimes you need to add a static route in pfSense to access the ISP device from your pfSense network. It can be a bit unsettling to look at your AT&T Broadband router and see the. This puts pfSense outside of the firewall but leaves the firewall on to protect the ISP device (very important!). You simply make sure pfSense is plugged into the LAN of the ISP device then go into the ISP device settings and enable the DMZ and add pfSense to the DMZ (usually by means of a something like a dropdown list of clients). You will usually find this somewhere near the firewall or advanced firewall settings inthe ISP device. ![]() If that wasn’t enough, you can find out what is listening on a TCP/IP port or set up a static TCP/IP route on Windows.Many of these ISP devices have the capability of creating a DMZ. Since you’re already finding IP addresses, you can also find the IP address of your Windows 10 or Windows 11 PC, including from the Command Prompt, or your iPhone, Roku, printer, Wi-Fi router, or other device. ![]() Just look under the network connection settings for anything listing a gateway, router, or default route address. Any device that allows you to connect to the network and view information about the network connection should display it. Look for the IP address displayed next to “Default Route” or “Gateway.”Īnd now that you know generally what to look for and where, you should also be able to find your router’s IP address without too much trouble on devices we haven’t covered, too. Typically, you can click this network icon and then select “Connection Information”-or something similar. Most Linux desktops have a network icon in their notification area. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |